When you've located a target and dug the hole, use the Bullseye II Pinpointer to precisely "pinpoint" the target. No tuning. Completely automatic. Works in either "vibration" or "beep" mode. Powerful LED light illuminates target areas when the button is pushed. Powered for up to 20 hours on a single 9-Volt battery.

36 kHz operating frequency, doesn't interfere with any other metal
detector.

P/N 812-0002

Everything you need to start panning for gold. 15" Gold Pan, Pan for Gold The Basics book, 50 Gold Facts booklet, suction bottle, pipet, display vial, stainless tweezers, magnifier and logo sports bag.
P/N 802-8069-1

Protects the Bullseye II from mud and moisture. Conveniently clips on to your belt or pocket. Pouch stays on continuously during use.
P/N 601-1216

Converts handheld Surfmasters to short rod for scuba use.
P/N 802-5195-1

This colorful White's Electronics patch measures 2"x3" and has an iron-on backing.
P/N 602-1132

Mounts to control box using existing control box screws. Keeps control box out of wet grass and off abrasive ground.
P/N 502-0028

Fit's past models that have a large control box.(5900) Mounts to control
box using existing control box screws. Keeps control box out of wet grass
and off abrasive ground. Also fits the TDI and TDI Pro.
P/N 502-0115-1

Plastic strips have common coins, trash targets, and a mineral sample attached for easy bench testing.
P/N 601-1130

Maroon plastic gold pan allows easy view of black sands and gold. Large 15" size with 3 layer built in ripples on one-third of pan edge.
P/N 601-0151-1

Converts Classics and early Goldmaster models from the standard two-piece rod assembly to a three-section assembly for tighter packing. (Does not fit Classic SL series instruments.)
P/N 802-5236

Handheld aluminum sand scoop. Rubberized grip. Heavy duty, hand-built construction. Handle is reversible.
P/N 601-0070

Handheld convertible (Short / Long) Sand Scoop. Spring Clip disassembles for travel/storage.
P/N 601-0069

8" steel shaft with brazed ball bearing tip. 4" wire wrapped wood handle.
P/N 601-1128-1

Black rubber handle. Six and one-half inch stainless steel blade with inches labeled.

Color may vary.
P/N 601-1145-1

White canvas material with White's logo and separate trash and treasure pouches.
P/N 601-0024

Detector cover. Resistant to water and dirt. Fits V3, DFX, XLT, MXT, and M6.
(one piece)
P/N 601-1155

Fits V3, DFX, XLT, QXT. Mounts to existing control box screws. Keeps control box off abrasive ground.
P/N 802-5260

Fits older full size control box models which use four "C" batteries.
P/N 802-5259

Extends loop cable length by approximately 5'. Replacement extension for hipmount kits manufactured from 1979 through 1988.
P/N 802-7022

Extends loop cable length approximately 5'. Heavy duty for the DFX and MXT.
P/N 802-7205

Protects speaker from dirt and moisture.
P/N 624-0264

Rugged but comfortable design. Easy to put on and take off.
P/N 602-1113

Replacement absorbent silica draws moisture away from internal components.
P/N 627-0045

Separate pouches for trash, treasure, and additional digging tools. (Belt not included)
P/N 601-0066

Ultimate trowel. Heat tempered, serrated edge. Sheath included.
P/N 601-0067

Security Handheld Holster.
P/N 601-1223

Thicker material than standard. Recommended for heavy sand, brush, or water use. Non adjustment hole position. Comes with arm cup strap.
P/N 802-5257

Pair (2) Peel & Stick rubber feet. 1/2 inch rise. Replacement for lost or worm original equipment or add to any detector model.
P/N 802-5312